Vignette d'image

Valley, Benoît

Nom
Valley, Benoît
Affiliation principale
Site web
Fonction
Professeur ordinaire
Email
benoit.valley@unine.ch
Identifiants
https://libra.unine.ch/handle/123456789/943
_
0000-0003-4632-0504

Résultat de la recherche

Filtres

3
3
3
Réinitialiser les filtres

Paramètres

Voici les éléments 1 - 3 sur 3
  • Publication
    Accès libre
    In Situ Direct Displacement Information on Fault Reactivation During Fluid Injection
    (2020-8)
    Kakurina, Maria 
    ;
    Guglielmi, Y.
    ;
    Nussbaum, Ch.
    ;
    Valley, Benoît 
    The three dimensional (3D) displacement induced by fluid injection was measured during two fault reactivation experiments conducted in carbonate rocks at the Rustrel Low Noise Underground Laboratory (LSBB URL), France, and in shale rocks at the Mont Terri Rock laboratory, Switzerland. The faults were activated by injecting high pressure fluid and using the Step-Rate Injection Method for Fracture In-Situ Properties, which allows a coupled pressure-flowrate-3D displacement monitoring in boreholes. Both experiments mainly show complex aseismic deformation of preexisting fractures that depend on (1) the fluid pressure variations related to chamber pressurization and leakage into the formation and (2) irreversible shear slip and opening of the reactivated fractures. Here we detail the processing of the 3D displacement data from both experiments to isolate slip vectors from the complex displacement signal. Firstly, we explain the test protocol and describe the in situ hydromechanical behavior of the borehole/fault system. Secondly, we define the methodology of the displacement data processing to isolate slip vectors with high displacement rates, which carry information about the key orientation of fault reactivation. Finally, we discuss which slip vectors can potentially be used to solve the stress inversion problem.
  • Publication
    Accès libre
    Slip perturbation during fault reactivation by a fluid injection
    (2019-2)
    Kakurina, Maria 
    ;
    Guglielmi, Y.
    ;
    Nussbaum, Ch.
    ;
    Valley, Benoît 
    Slip orientation inferred from fault striae or focal mechanism datasets is commonly used in stress inversion methods based on the Wallace-Bott hypothesis. The hypothesis postulates that slip on a fault plane is collinear with the orientation of the resolved shear stress. It is valid for a single planar fault subjected to a homogeneous far-field stress. However, the experimental displacement data from an induced fault reactivation experiment, conducted in the Mont Terri rock laboratory, Switzerland, indicated multiple triggered slip orientations, thereby preventing application of the above inversion method. We present numerical and analytical results of slip on a reactivated fracture with a non-uniform fluid pressure distribution. Using these models, we evaluate the reasons for the inconsistency of our observations and the traditional Wallace-Bott hypothesis and test the physical effects of various parameters on fault slip. In the fully coupled hydromechanical numerical model (three-dimensional distinct element method), fluid pressure at a point on the fault surface is increased stepwise (assumed planar and singular) until shear reactivation of the fault is induced. We studied two different models with high and low fault plane stiffness to represent hard and soft rock masses, respectively. The model shows that high fault stiffness preserves the planarity of the fault plane, while low fault stiffness permits dilation and morphological changes of the fracture related to fluid pressure diffusion. The highest slip perturbation was observed in the low stiffness model due to the change of the fracture shape, controlled by the non-uniform pressure distribution. The Eshelby analytical solution confirmed that the more the fracture is dilated, the more the corresponding resolved shear stress is perturbed. Additionally, when compared to dilation and fault aperture, the friction angle has the most influence on the angular difference between geomechanical slip vectors and resolved shear stress.
  • Publication
    Accès libre
    Stress Measurements for an In Situ Stimulation Experiment in Crystalline Rock: Integration of Induced Seismicity, Stress Relief and Hydraulic Methods
    (2018-9)
    Krietsch, H.
    ;
    Gischig, V.
    ;
    Evans, K. F.
    ;
    Doetsch, J.
    ;
    Dutler, Nathan 
    ;
    Valley, Benoît 
    ;
    Amann, F.
    An extensive campaign to characterize rock stresses on the decameter scale was carried out in three 18–24 m long boreholes drilled from a tunnel in foliated granite at the Grimsel Test Site, Switzerland. The survey combined stress relief methods with hydrofracturing (HF) tests and concomitant monitoring of induced seismicity. Hydrofracture traces at the borehole wall were visualized with impression packer tests. The microseismic clouds indicate sub-vertical south-dipping HFs. Initial inversion of the overcoring strains with an isotropic rock model yielded stress tensors that disagreed with the HF and microseismic results. The discrepancy was eliminated using a transversely isotropic rock model, parametrized by a novel method that used numerical modelling of the in situ biaxial cell data to determine the requisite five independent elastic parameters. The results show that stress is reasonably uniform in the rock volume that lies to the south of a shear zone that cuts the NNW of the study volume. Stress in this volume is considered to be unperturbed by structures, and has principal stress magnitudes of 13.1–14.4 MPa for σ1, 9.2–10.2 MPa for σ2, and 8.6–9.7 MPa for σ3 with σ1 plunging to the east at 30–40°. To the NNW of the uniform stress regime, the minimum principal stress declines and the principal axes rotate as the shear zone is approached. The stress perturbation is clearly associated with the shear zone, and may reflect the presence of more fragmented rock acting as a compliant inclusion, or remnant stresses arising from slip on the shear zone in the past.